Gesamt: €0,00
【Technologia śledzenia 99%】Regulator ładowania słonecznego LiTime 30A MPPT z zaawansowaną technologią śledzenia punktu maksymalnej mocy może stale śledzić maksymalny punkt mocy układu, aby uzyskać maksymalną ilość energii do ładowania akumulatora. Wydajność śledzenia wynosi nie mniej niż 99%, a szczytowa wydajność konwersji wynosi do 98%.
【Funkcja Bluetooth】Kontroler LiTime 12 V/24 V MPPT jest wyposażony w port komunikacyjny RS232/Bluetooth umożliwiający podłączenie adaptera Bluetooth z portem RJ12 (w zestawie), co umożliwia użytkownikowi zdalne monitorowanie w czasie rzeczywistym stanu panelu słonecznego, akumulatora i obciążeń.
【Ekran LCD i wskaźniki LED】Kontroler LiTime MPPT jest wyposażony w ekran LCD do wyświetlania informacji o działaniu systemu i cztery przyciski do nawigacji po menu. Ponadto wiele wskaźników LED pomaga wskazać stan panelu słonecznego, akumulatora, obciążeń i kontrolera.
【Doskonałe odprowadzanie ciepła i wiele zabezpieczeń】Kontroler LiTime MPPT jest wykonany z odlewanego ciśnieniowo aluminium, co zapewnia doskonałe odprowadzanie ciepła w celu zmniejszenia utraty mocy. Ponadto wiele zabezpieczeń wbudowanych w kontroler ładowania słonecznego zapewnia pełną ochronę kontrolera przed odwrotnym podłączeniem, przepięciem, przepięciem, zwarciem i przegrzaniem.
【Dotyczy akumulatorów LiFePO4, kwasowo-ołowiowych】Regulator ładowania słonecznego LiTime 12V/24V 30A MPPT jest domyślnie skonfigurowany do akumulatorów LiFePO4 12 V. Jednak jest on również kompatybilny z akumulatorami LiFePO4 24 V, uszczelnionymi i żelowymi kwasowo-ołowiowymi poprzez dostosowanie parametrów.
Weight: 2kg (4.41 lbs)
Protection Class: IP32
Communication Method: RS485 (RJ12)/Inbuilt BT
Dimensions: L9.65 * W7.09 * H3.25 in (L245 * W180 * H82.5 mm)
Warranty: 3 years
System Voltage: 12V/24V/Auto
No-Load Loss: 12mA at 12V/10mA at 24V
Battery Voltage: 9V - 32V
Max. Solar Input Voltage: 100V
Max. Power Point Voltage Range: Battery Voltage + 3V to 76V
Rated Charging Current: 30A
Rated Load Current: 20A
Max. Capacitive Load Capacity: 8000uF
Max. Solar Panel System Input Power: 450W for 12V/900W for 24V
Conversion Efficiency: ≤97%
MPPT Tracking Efficiency: > 99.9%
Nominal Voltage: 12.8V
Temperature Compensation Factor: -3mv/℉ or ℃/2V (Default)
Operating Temperature: -31℉ ~ 113℉ (-35℃ ~ 45℃)
Altitude: ≤ 3000m
System Voltage: 12V/24V/Auto
No-Load Loss: 0.7W - 1.2W
A: The LiTime 12V/24V 30A MPPT Solar Charge Controller can work with standard off-grid 12/24V solar panels with high voltage or multiple panels with voltage up to 100V. And the maximum combined input solar power is 450W for a 12V battery system or 900W for a 24V system. LiTime 12V/24V 30A MPPT Solar Charge Controller's default setting is for 12V LiFePO4 battery. But it's also compatible for 24V LiFePO4 battery, Sealed, Gel Lead-acid batteries by adjusting the parameters.
A: There is a practical limit though, if the solar array is too large then the power is just wasted, since the charge controller is always limiting the output. A typical recommendation is to limit the solar array to 110%-125% of the maximum controller rating.
A: LiTime solar charge controllers regulate the current from the panels to a safe level so it can charge the batteries. A 30A controller is adequate for a 300 watt solar panel set up.
A: LiTime solar charge controllers use maximum power point tracking (MPPT) technology which optimize solar production and control the battery charging voltage to prevent overcharging.
A: When the battery voltage reaches a point where the battery charger decides that the battery is full, the charger will cut out, and stop drawing power from the MPPT controller. In other words, the battery charger will present a high impedance to the MPPT controller.
A: No! MPPT solar charge controllers help to flow the current efficiently into your depleted battery. If we connect an MPPT solar charge controller directly to the inverter, your soalr system can get damaged, but if not damaged, there will be zero input in the inverter. So connecting MPPTs directly to the inverter is a bad idea!
A: You take the total watts of the solar array divided by the voltage of the battery bank. That will give you the output current of the soalr charge controller. For example, a 1000W solar array ÷ 24V battery bank = 41.6A. The rating of the charge controller should be at least 40A.